After encountering frequent misunderstandings of rock compressibility and its applications, I decided to write a series of posts on ‘geomechanics of compressibility’ to explain its rock mechanical definition, its different types, methods of compressibility measurement and their differences and the parameters affecting this property especially stress path and hysteresis. As an introductory post, let’s start with explaining why compressibility is important to us. But wait a moment! If you feel the equations are eyesores just ignore them, I don’t think it will really matter.

**Fluid Flow Analysis**

Pore volume compressibility (*C _{p}*) has long been recognized as an important factor in fluid flow simulation for aquifers and reservoirs as shown by the following fundamental equation of fluid flow in porous media:

*(C _{p}+C_{l})ρφ ∂p/∂t+∇.(-k/μ(∇p+ρg∇z)=q *

*[In this equation, C _{l} is fluid compressibility, ρ is pore fluid density, φ is rock porosity, g is gravity acceleration, q is the source term, k is permeability, t is time and z is the elevation measured in the vertical direction oriented downward.]*

Generally, in either of fluid flow simulations or material-balance calculations, the role of pore volume compressibility coefficient (*C _{p}*) becomes increasingly important as the fluid compressibility decreases. The importance of pore volume compressibility is even more crucial for closed systems where, in absence of fluid flux, fluid flow and pressure changes are controlled mainly by pore volume changes.

**Hydrocarbon Reserve Estimation and Storage Capacity Evaluation**

Pore volume compressibility is also important in volumetric estimation of hydrocarbon reserves (find more in here) and evaluation of fluid storage capacity and efficiency in aquifers (for instance, waste fluid disposal or *CO _{2}* sequestration). As a simple example, in estimation of storage capacity of closed-system aquifers, the efficiency factor (

*E*) for storage is introduced by Zhou et al. (2008) as:

_{i}*E _{i}=(C_{p}+C_{w} )Δp*

*[where C _{w} is the compressibility of water and Δp is the average pressure increase within the aquifer induced by injection.]*

**Approximation of Porosity Variation**

Another application of pore volume compressibility is for the estimation of porosity change induced by pore pressure variation within a reservoir. The following equation is widely used for porosity approximation of consolidated and cemented reservoir rocks (e.g., Satter et al., 2008):

*φ _{2}=φ_{1} exp(C_{p}(p_{2}-p_{1}))*

*[where φ _{1} and φ_{2} are the values of porosity, at reservoir pressures of p_{1} and p_{2}, respectively.]*

Such relations are the most simplistic way of involving geomechanics in fluid flow simulation. However, as it can bee seen in Figure 3, such relations must be used with the most caution as I will discuss it in detail later in this series.

**Estimation of Ground Deformation**

Bulk volume compressibility coefficient, when measured using a uniaxial pore volume test, can be directly used for calculation of reservoir or aquifer contraction or expansion induced by production or injection.

In general, the expansion of *ΔH* induced by the average pore pressure increase of *Δp* in a reservoir or an aquifer with an average height (thickness) of *H* may be calculated from the following equation:

*ΔH= C _{bu}ΔpH*

*[where C _{bu} is uniaxial compressibility.]*

Some rocks, such as consolidated sandstones, behave elastically when stresses are less than critical yield stresses. Rocks show more elastic responses when pore pressure is increased e.g., in the case of waste fluid disposal or CO2 sequestration (Fjær et al., 2008). When rock behaviour is isotropic and elastic, the following relation exists between uniaxial bulk compressibility and rock elastic parameters:

*C _{bu}=((1-2υ)(1+υ))/(E(1-υ))*

*[where υ is Poisson’s ratio and E is Young’s modulus of the rock.]*

Hence, in absence of other reliable data, bulk volume compressibility can be used as an auxiliary parameter for estimating elastic properties of the rock.

**Calculation of Biot’s Coefficient**

Bulk volume compressibility coefficient (*C _{b}*) may also be implemented in the following equation to estimate Biot’s coefficient (

*α*) as a key parameter required for any geomechanical analysis:

*α=1-C _{m}/C_{b} *

where *C _{m}* is the matrix (or grain) compressibility and can be measured using an unjacketed hydrostatic test, or it can be estimated from the mineralogical composition of the rock (Zimmerman,1991).

**Read the second part of this series here.**

**References**

Hall, H.N., 1953. Compressibility of Reservoir Rocks, Journal of Petroleum Engineering, 5(1).

Zimmerman, R.W. 1991. Compressibility of Sandstones, Elsevier, Amsterdam, 173 p.